Skip to main content

mobile jammer with circuit diagram

Simple Mobile Jammer Circuit Diagram:

Mobile Jammer Circuit Diagram Simple Mobile Jammer Circuit Diagram

Cell Phone Jammer Circuit Explanation:

  • If you understand the above circuit, this circuit analysis is simple and easy. For any jammer circuit, remember that there are three main important circuits. When they are combined together, the output of that circuit will work as a jammer. The three circuits are
    1. RF amplifier.
    2. Voltage controlled oscillator.
    3. Tuning circuit.
  • So the transistor Q1, capacitors C4 & C5 and resistor R1 constitute the RF amplifier circuit. This will amplify the signal generated by the tuned circuit. The amplification signal is given to the antenna through C6 capacitor. Capacitor C6 will remove the DC and allow only the AC signal which is transmitted in the air.
  • When the transistor Q1 is turned ON, the tuned circuit at the collector will get turned ON. The tuned circuit consists of capacitor C1 and inductor L1. This tuned circuit will act as an oscillator with zero resistance.
  • This oscillator or tuned circuit will produce the very high frequency with minimum damping. The both inductor and capacitor of tuned circuit will oscillate at its resonating frequency.
  • The tuned circuit operation is very simple and easy to understand. When the circuit gets ON, the voltage is stored by the capacitor according to its capacity. The main function of capacitor is to store electric energy. Once the capacitor is completely charged, it will allow the charge to flow through inductor. We know that inductor is used to store magnetic energy. When the current is flowing across the inductor, it will store the magnetic energy by this voltage across the capacitor and will get decreased, at some point complete magnetic energy is stored by inductor and the charge or voltage across the capacitor will be zero. The magnetic charge through the inductor will decreased and the current will charge the capacitor in opposite or reverse polarity manner. Again after some period of time, capacitor will get completely charged and magnetic energy across the inductor will be completely zero. Again the capacitor will give charge to the inductor and becomes zero. After some time, inductor will give charge to capacitor and become zero and they will oscillate and generate the frequency.
  • This circle run upto the internal resistance is generated and oscillations will get stop. RF amplifier feed is given through the capacitor C5 to the collector terminal before C6 for gain or like a boost signal to the tuned circuit signal. The capacitors C2 and C3 are used for generating the noise for the frequency generated by the tuned circuit. Capacitors C2 and C3 will generate the electronic pulses in some random fashion (technically called noise).
  • The feedback back or boost given by the RF amplifier, frequency generated by the tuned circuit, the noise signal generated by the capacitors C2 and C3 will be combined, amplified and transmitted to the air.
  • Cell phone works at the frequency of 450 MHz frequency. To block this 450MHz frequency, we also need to generate 450Mhz frequency with some noise which will act as simple blocking signal, because cell phone receiver will not be able to understand to which signal it has been received. By this, we can able to block the cell phone signal from reaching the cell phones.
  • So here in the above circuit, we generated the 450 MHz frequency to block the actual cell phone signal. That’s what the above circuit will act as a jammer for blocking the actual signal.
Note:
  • This circuit will work in the range of 100 meters i.e. it can block the signals of cell phones with in 100 meters radius.
  • Usage of this type of circuits is banned in most of the countries. Usage of this circuit is illegal and if you caught by using this circuit, you can be imprisoned and also should pay large amount in the form of fine.
  • This circuit can be used in TV transmission and also for remote controlled toys or play things.
  • If the circuit is not working, just increase the resistor and capacitors values in the circuit. Increase the frequency of tuned circuit by using this formula F= 1/ (2*pi*sqrt (L*C)). Increase the inductor capacitor circuit components value for increasing the frequency.

contact:
 DEV HARSHA
whatsapp,hike nd calls
8978511693 & 9505630317

Comments

Unknown said…
I'm glad to have visited your blog and good to know you! I find it interesting and informative.
mobile signal Jammer

Popular posts from this blog

LED DIMMER WITH CIRCUIT DIAGRAM

In this circuit, at the starting LED glow slowly, then grown brighter and once again slowly it became dim. The basis of the whole circuit is an operational amplifier IC named LM358. Circuit Diagram of LED Lamp Dimmer: LED Lamp Dimmer Circuit Diagram – ElectronicsHub.Org Working of LED Lamp Dimmer Circuit: LM358 is mainly made up of a package which contains two not dependent operational  amplifiers of high gain. The most significant attribute of these IC is that we have no need of the  independent power supply for the functioning of each comparator till the large range of the power supply. LM358 can be employed like transducer amplifier or can be worked as DC gain block etc. The huge DC voltage gain of the LM358 IC is 100db. For the only power supply this IC can work on the voltage range of 3V to 32V while for the twin power supply this IC work on the range of ±1. 5V to ±16V . And moreover large output voltage is also supported by it. Related Post: PWM L...

Automatic Railway Gate Controller with Circuit Diagram

The main aim of this project is to operate and control the unmanned railway gate in the proper manner in order to avoid the accidents in the unmanned railway crossing. In a country like ours where there are many unmanned railway crossings, accidents are increasing day by day. These train accidents are due to the absence of human power in the railway. In order to overcome the accidents due to the above problem we have planned to design the project. Automatic Railway Gate Control System with High Speed Alerting System is an innovative circuit which automatically controls the operation of railway gates detecting the arrival and departure of trains at the gate. It has detectors at the far away distance on the railway track which allows us to know the arrival and departure of the train. These detectors are given to microcontroller which activates the motors which open/close the railway gate correspondingly. Another feature of this circuit is that it has an intellige...

Rain Alarm Project

Water is basic need in every one’s life. Saving and proper usage of water is very important. Here is an easy project which will give the alarm when there is rain, so that we can make some actions and save the rain water. As a result, we can increase the water levels of underground water by using underwater recharge technique. Rain water detector will detect the rain and make an alert; rain water detector is used in the irrigation field, home automation, communication, automobiles etc. Here is the simple and reliable circuit of rain water detector which can be constructed at low cost. Rain Alarm Project Block Diagram: Rain water sensor is the main component in the circuit. For this rain sensor, no need to go and buy in the market or online. We can do it ourselves just by taking the piece of Bakelite or mica board and aluminum wire. Bakelite or mica board should be made completely flat and aluminum wire should be pasted on the flat board as shown in the figure below o...